ARCHIVE
january 2023
december 2022
november 2022
october 2022
september 2022
august 2022
july 2022
june 2022
may 2022
april 2022
march 2022
february 2022
december 2021
november 2021
october 2021
september 2021
august 2021
july 2021
april 2021
march 2021
february 2021
january 2021
december 2020
november 2020
october 2020
september 2020
august 2020
july 2020
june 2020
may 2020
april 2020
march 2020
february 2020
january 2020
december 2019
october 2019
august 2019
may 2019
march 2019
february 2019
january 2019
december 2018
november 2018
october 2018
september 2018
august 2018
july 2018
april 2018
march 2018
february 2018
january 2018
december 2017
november 2017
october 2017
september 2017
august 2017
july 2017
june 2017
may 2017
april 2017
march 2017
february 2017
january 2017
december 2016
november 2016
october 2016
september 2016
august 2016
july 2016
june 2016
may 2016
april 2016
march 2016
february 2016
january 2016
december 2015
november 2015
october 2015
september 2015
august 2015
july 2015
june 2015
may 2015
april 2015
march 2015
february 2015
january 2015
december 2014
november 2014
october 2014
september 2014
august 2014
july 2014
june 2014
may 2014
april 2014
march 2014
february 2014
january 2014
december 2013
november 2013
october 2013
september 2013
august 2013
july 2013
june 2013
may 2013
april 2013
march 2013
february 2013
january 2013
april 2011

Blog


Air venting valves and accumulations in systems
Why should you install an air venting valve?  The main reason is to eliminate the air and gas that accumulate in some areas of the system and which can prevent the fluid from flowing correctly through it. Air pockets can appear as a result of many different causes, but the main ones are: [...]
25/05/2017

Manifolds for water and multilayer pipes
One of the most appreciated solutions to distribution in hot water systems is manifolds for water, made of stamped brass and worked on cutting-edge transfer machinery. These manifolds for water can be installed quickly without having to create chased intersections if combined with fittings for [...]
18/05/2017

Electric resistors for water heaters and the problem of system corrosion
Electric resistors for water heaters induce vagrant currents into circuits which can favour spot corrosion. This damages the system components, starting from the electric resistors and ending with the boiler walls. Sacrificial anodes of magnesium are usually installed to protect these [...]
11/05/2017

Manifolds for water heating systems and stress corrosion.
To keep water heating systems safe and long lasting, it is difficult not to think about using manifolds. These very versatile articles are made from brass and, thanks to their modularity, they can satisfy the most varied project requirements. The use of manifolds for water heating systems [...]
27/04/2017

PVC flexible hoses with fabric reinforcement
In the specific section of our catalogue you can find PVC flexible hoses already cut to size and headed with specific fittings for connection between the gas cylinder and the relative user, or in 100 m rolls to be cut to the required length. The characteristics of these PVC flexible hoses are [...]
20/04/2017

Life cycle of reducers for water
All the reducers for both water and gas made in our factory are sold to clients with a calibration and compliance certificate, after they pass bench inspections and calibration. The life cycle of these products begins from their cataloguing and the study of the most suitable process for their [...]
13/04/2017

Gas fittings: construction and sealant
Brass is a versatile material and it is perfect for many different uses, among which for producing gas fittings. These items, which are usually indicated as generic fittings, in the majority of cases are produced starting from coarse material that is hot forged and subsequently processed by [...]
06/04/2017

Materials for producing air release valves
We use the best materials available on the market to make our air release valves, starting from the body made of CW617N that is hot-forged and then processed on computerised numeric control transfer machines that guarantee constant process repeatability. This brass has the perfect combination of [...]
30/03/2017

The importance of the specific power of electric resistances
The correct choice of the specific power when designing and making tubular electric resistances is a necessary condition for making this device operate correctly when in contact with water and powered by the power supply voltage. The maximum surface load of our electric resistances is 9 [...]
23/03/2017

Competitive brass hydraulic fittings processing
The correct quality-price ratio when producing brass hydraulic fittings, often called generic fittings, can only be obtained with cutting-edge machines combined with purposely-studied tools that make it possible to carry out multiple processing in a single operation. The study of the tool shape [...]
16/03/2017

Page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
I contenuti di questo sito non hanno carattere di periodicità e non rappresentano 'prodotto editoriale'.